View RHFL4913KP15-02V_6646239.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

october 2008 rev 9 1/19 19 rhfl4913xx15 - rhfl4913xx25 rhfl4913xx33 - rhfl4913xx50 rad-hard positive fixed voltage regulator features 2 and 3 a low dropout voltage embedded overtemperature, overcurrent protections adjustable curr ent limitation output overload m onitoring/signalling fixed 1.5 v, 2.5 v; 3.3 v; 5.0 v output voltages inhibit (on/off) ttl-compatible control programmable output short-circuit current remote sensing operation rad-hard: tested up to 300 krad mil std 883e method 1019.6 and low dose rate conditions heavy ions sel immune description the rhfl4913 fixed is a high performance rad- hard positive voltage regulator family. available into various hermetic ceramic packages, it is specifically intended for space and harsh radiation environments. input supply range is up to 12 v. rhfl4913 fixed is qml-v qualified, dscc smd are 5962f02534 / 02535 / 02536. smd.5 to-257 flat-16 figure 1. block diagram for package smd.5 and to-257 www.st.com
contents rhfl4913xx15 - rhfl4913xx25 - rhfl4913xx33 - rhfl4913xx50 2/19 contents 1 diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5 device description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 5.1 low pin count package limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 5.2 sense pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 5.3 inhibit on-off control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 5.4 overtemperature protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 5.5 overcurrent protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 5.6 ocm pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 5.7 alternate to . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 6 application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 6.1 remote sensing operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 7 notes about flat-16 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 7.1 radiation performances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 7.2 die information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 8 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 9 ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 10 revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
rhfl4913xx15 - rhfl4913xx25 - rhfl4913xx33 - rhfl4913xx50 diagram 3/19 1 diagram figure 2. block diagram for package flat-16
pin configuration rhfl4913xx15 - rhfl4913xx25 - rhfl4913xx33 - rhfl4913xx50 4/19 2 pin configuration figure 3. pin configuration (top view for flat-16, bottom view for smd.5) to-257 smd.5 flat-16 table 1. pin description pin name flat-16 smd.5 to-257 v o 1, 2, 6, 7 1 3 v i 3, 4, 5 2 1 gnd 13 3 2 i sc 8 ocm 10 inhibit 14 sense 16 nc 9, 11, 12, 15
rhfl4913xx15 - rhfl4913xx25 - rhfl4913xx33 - rhfl4913xx50 maximum ratings 5/19 3 maximum ratings table 2. absolute maximum ratings (1) 1. exceeding maximum ratings may damage the device. symbol parameter value unit v i dc input voltage, v i - v ground 14 v i o output current rhfl4913s, esy 3 a rhfl4913kp 2 p d t c = 25c power dissipation kp, s versions 15 w esy version 10 t stg storage temperature range -65 to +150 c t op operating junction temperature range -55 to +150 c t j junction temperature (2) 2. internally limited to about maximum +175 c by thermal shutdown circuit. +150 c esd electrostatic discharge capability class 3 table 3. thermal data symbol parameter flat-16 to-257 smd.5 unit r thjc thermal resistance junction-case max. 8.3 12.5 8.3 c/w t sold maximum soldering temperature, 10 sec. 300 c
electrical characteristics rhfl4913xx15 - rhfl4913xx25 - rhfl4913xx33 - rhfl4913xx50 6/19 4 electrical characteristics table 4. electrical characteristics (t j = 25 c, v i = v o +2.5 v, c i = c o = 1 f, unless otherwise specified) symbol parameter test conditions min. typ. max. unit v i operating input voltage i o = 2 a (flat-16) or 3a (smd.5 & to-257) 12 v v o output voltage accuracy v i = v o +2.5v, i o = 5ma -2 2 % i short output current limit (1) adjustable by mask/external resistor 4.5 a v o operating output voltage i o = 2 a, 1.5 v output voltage 1.47 1.53 v v o operating output voltage i o = 2 a, 2.5 v output voltage 2.45 2.55 v v o operating output voltage i o = 2 a, 3.3 v output voltage 3.23 3.37 v v o operating output voltage i o = 2 a, 5.0 v output voltage 4.9 5.1 v v o / v i line regulation v i = v o +2.5v to 12 v, i o = 5ma (+25c) 0.3 % v i = v o +2.5v to 12 v, i o = 5ma (-55c) 0.4 % v i = v o +2.5v to 12 v, i o = 5ma (+125c) 0.4 % v o / v o load regulation v i = v o +2.5v, i o = 5ma to 400 ma (+25c) 0.2 % v i = v o +2.5v, i o = 5ma to 400 ma (-55c) 0.3 % v i = v o +2.5v, i o = 5ma to 400 ma (+125c) 0.3 % v i = v o +2.5v, i o = 5ma to 1a (+25c) 0.3 % v i = v o +2.5v, i o = 5ma to 1a (-55c) 0.4 % v i = v o +2.5v, i o = 5ma to 1a (+125c) 0.4 % z out output impedance i o = 100 ma dc and 20 ma rms 100 m i q quiescent current v i = v o +2.5v, i o = 30ma, on mode 8 ma v i = v o +2.5v, i o = 300ma, on mode 25 v i = v o +2.5v, i o = 1a, on mode 60 v i = v o +2.5v, i o = 3a, on mode (only for smd.5 and to-257) 150 v i = v o +2v, v inh = 2.4v, off mode 1 i q quiescent current v i =v o +2.5v, i o = 1a, t j =+125c, on mode 40 ma v i =v o +2.5v, i o = 1a, t j =-55c, on mode 100
rhfl4913xx15 - rhfl4913xx25 - rhfl4913xx33 - rhfl4913xx50 electrical characteristics 7/19 v d dropout voltage i o = 400ma, t j = -55c 300 400 mv i o = 400ma, t j = +25c 350 450 i o = 400ma, t j = +125c 450 550 i o = 1a, t j = -55c 550 i o = 1a, t j = +25c 650 i o = 1a, t j = +125c 800 i o = 2a, t j = +25c 750 i o = 2a, t j = +125c 950 v inh(on) inhibit voltage i o = 5ma, t j = -55 to 125c 0.8 v v inh(off) inhibit voltage i o = 5ma, t j = -55 to 125c 2.4 v svr supply voltage rejection (1) v i = v o +2.5v 1v, i o = 5ma f = 120hz 60 70 db f = 33khz 30 40 i sh shutdown input current v inh = 5 v 15 a v ocm ocm pin voltage sinked i ocm = 24 ma active low 0.38 v t plh t phl inhibit propagation delay (1) v i = v o +2.5v, v inh = 2.4 v, i o = 400 ma on-off 20 s off-on 100 s en output noise voltage (1) b= 10hz to 100khz, i o = 5ma to 2a 40 vrms 1. this value is guaranteed by design. for each application it?s strongly recommended to comply with the maximum current limit of the package used. table 4. electrical characteristics (continued) (t j = 25 c, v i = v o +2.5 v, c i = c o = 1 f, unless otherwise specified) symbol parameter test conditions min. typ. max. unit figure 4. application diagram for remote sensing operation
device description rhfl4913xx15 - rhfl4913xx25 - rhfl4913xx33 - rhfl4913xx50 8/19 5 device description the rhfl4913 fixed voltage contains a pnp type power element controlled by a signal resulting from amplified comparison between the internal temperature compensated band- gap cell and the fraction of the desired output volt age value. this fractional value is obtained from an internal-to-die resistor divider bridge set by stmicroelectronics. the device is protected by several functional blocks. 5.1 low pin count package limitations some functions (inhibit, ocm, sense) are not available due to lack of pins. corresponding die pads are by def ault connected inside silicon. 5.2 sense pin the load voltage is applied by a kelvin line connected to sense pin: voltage feed-back comes from the internal divider resistor bridge. therefore possible output voltages are set by manufacturer mask metal options. sense pin is not available in 3pin packages. 5.3 inhibit on-off control by setting inhibit pin ttl-high, the device switches off the output current and voltage. the device is on when inhibit pin is set low. since inhibit pin is internally pulled down, it can be left floating in ca se inhibit function is not utilized. i nhibit pin is not available in 3pin packages. 5.4 overtemperature protection a temperature detector internally monitors the power element junction temperature. the device goes off at approx. 175 c, returning to on mode when back to approx. 40 c. it is worth noting that when the internal temperature detector reaches 175 c, the active power element can be at 225 c: device reliability cannot be granted in case of extensive operation under these conditions. 5.5 overcurrent protection i sc pin. an internal non-fold back short-circuit limitation is set with i short > 3.8 a (v o is 0 v). this value can be reduced by an external resistor connected between i sc pin and v i pin, with a typical value range of 10 k to 200 k . this adjustment feature is not available in 3 pin packages. to keep excellent v o regulation, it is necessary to set i short 1.6 times greater than the maximum desired application i o . when i o reaches i short ? 300 ma, the current limiter overru les regulation and v o starts to drop and the ocm flag is risen. when no current limitation adjust ment is required, i sc pin must be left unbiased (as it is in 3 pin packages).
rhfl4913xx15 - rhfl4913xx25 - rhfl4913xx33 - rhfl4913xx50 device description 9/19 5.6 ocm pin goes low when current limiter st arts to be active, otherwise v ocm = v i . it is bufferized and can sink 10 ma. ocm pin is internally pulled-up by a 5 k resistor. not available in 3 pin packages. 5.7 alternate to rhfl4913 fixed (& custom) voltages replace all 3-terminal industry devices, providing essential benefits - lower drop-out - high radiation performance - better svr - saving the high stability external setting resistors.
application information rhfl4913xx15 - rhfl4913xx25 - rhfl4913xx33 - rhfl4913xx50 10/19 6 application information the rhfl4913 fixed voltage is functional as soon as v i -v o voltage difference is slightly above the power element saturation voltage. a minimum 0.5 ma i o ensures perfect ?no- load? regulation. all available v i pins must always be externally interconnected, same thing for all available v o pins, otherwise device stability and reliab ility cannot be granted. all nc pins can be connected to ground. the inhibit function switches off the output current in an electronic way, that is very quickly. according to lenz?s law, external circuitry reacts with ?ldi/dt terms which can be of high amplitude in case some series-inductance exists. the effect would be a large transient voltage developed on both device terminals. it is necessary to protect the device with schottky diodes preventing negative voltage excursions. in the worst case, a 14 v zener diode shall protect the device input. the device has been designed for high stabilit y and low drop out oper ation: minimum 1 f input and output tantalum capacitors are therefore mandatory. capacitor esr range is from 0.01 to over 20 . such range turns out to be useful when esr increases at low temperature. when large transient currents are expected, larger value capacitors are necessary. in case of high current operation with expected short-circuit events, caution must be considered relatively to capacitors. they must be connected as close as possible to device terminals. as some tantalum capacitors may permanently fail when submitted to high charge-up surge currents, it is recommended to decouple them with 470 nf polyester capacitors. being rhfl4913 fixed voltage manufactured with very high speed bipolar technology 6 ghz f t transistors), the pcb lay-out must be performed with extreme care, very low inductance, low mutually coupling lines, otherwise high frequency parasitic signals may be picked-up by the device resulting into self-oscillation. user?s benefit is a svr perfor mance extended to far higher frequencies. 6.1 remote sensing operation in case the load is located far from the regulator, it is recommended to comply with the scheme below. to obtain the best regulation, it is in addition essential to care about: ? the wire connecting r2 to the load end must not be crossed by the load current (kelvin sense). the noise captured by the wires between the load and the chip could bring a noisy output voltage. in case this happens, it is recommended that shielded cables are used for these connections. the external wrap must be used for connecting the ground of the chip with the load ground. it is also recommended to place 1 f tantalum capacitors between output and ground close to the device and another next to the load.
rhfl4913xx15 - rhfl4913xx25 - rhfl4913xx33 - rhfl4913xx50 notes about flat-16 package 11/19 7 notes about flat-16 package the bottom of package is metallized to allow user to dire ctly solder the voltage regulator to the equipment heater, in order to optimize heat removal performance. 7.1 radiation performances the rhfl4913f has been tested against: 300krad tid elders in accordance with mil- 1019.6, bipolar section: post radiation parameters are within datasheet pre-rad limits. submitted to 200mev iodine ions of 60.4mev/cm2/mg let up to 1exp(+7) ions / cm2, no sel event has been detected. 7.2 die information rhfl4913 fixed is also available in die form. space dice are electrically tested by stmicroelectronics in such a way that, when mounted in proper thermal and electrical substrate, they provide full compliance with equivalent packaged product. - max die dimensions: 2.794 mm by 3.861 mm or 110 mils by 152 mils - die thickness: 357 m +/- 50 m - pad size: 184 m by 184 m - metallization: alumin um 4% silicon alloy - die backside: bare silicon - die backside potential: ground (*) die sense pad is active in rhfl4913 fixed die. it shall not be left unbonded. it should be bonded to v o pin. (**) die adjust pad is available in t he die lay-out but is not electrically c onnected to the ic. it shall be left unconnected during hybrid bonding. figure 5. die size
package mechanical data rhfl4913xx15 - rhfl4913xx25 - rhfl4913xx33 - rhfl4913xx50 12/19 8 package mechanical data in order to meet environmental requirements, st offers these devices in ecopack ? packages. these packages have a lead-free second level interconnect. the category of second level interconnect is marked on the package and on the inner box label, in compliance with jedec standard jesd97. the maximum ratings related to soldering conditions are also marked on the inner box label. ecopack is an st trademark. ecopack specifications are available at: www.st.com.
rhfl4913xx15 - rhfl4913xx25 - rhfl4913xx33 - rhfl4913xx50 package mechanical data 13/19 dim. mm. inch. min. typ. max. min. typ. max. a 2.16 2.72 0.0 8 5 0.107 b 0.4 3 0.017 c0.1 3 0.005 d 9 . 9 10. 39 0 e6. 9 1 0.272 e2 4. 3 2 0.170 e 3 0.76 0.0 3 0 e 1.27 0.050 l 6.72 0.265 q 0.66 1.14 0.026 0.045 s 1 0.1 3 0.005 flat-16 (mil- s td-1 83 5) mechanical data 7450 9 01a 1 8 16 e b c l e d s 1 q a e2 e 3 l e 3 9
package mechanical data rhfl4913xx15 - rhfl4913xx25 - rhfl4913xx33 - rhfl4913xx50 14/19 dim. mm. inch. min. typ. max. min. typ. max. a2. 8 4 3 .00 3 .15 0.112 0.11 8 0.124 a1 0.25 0. 38 0.51 0.010 0.015 0.020 b 7.1 3 7.26 7. 39 0.2 8 1 0.2 8 6 0.2 9 1 b 1 5.5 8 5.72 5. 8 4 0.220 0.225 0.2 3 0 b 2 2.2 8 2.41 2.54 0.0 9 0 0.0 9 5 0.100 b3 2. 9 2 3 .05 3 .1 8 0.115 0.120 0.125 d 10.0 3 10.16 10.2 8 0. 39 5 0.400 0.405 d1 0.76 0.0 3 0 e7. 39 7.52 7.64 0.2 9 1 0.2 9 60. 3 01 e1. 9 1 0.075 s md.5 mechanical data 7 38 64 3 4b e
rhfl4913xx15 - rhfl4913xx25 - rhfl4913xx33 - rhfl4913xx50 package mechanical data 15/19 dim. mm. inch. min. typ. max. min. typ. max. a 10.54 0.415 b 10.54 0.415 c 16.64 0.655 d 4.7 5. 33 0.1 8 5 0.210 e 1.02 0.40 f 3 .56 3 .6 83 . 8 1 0.140 0.145 0.150 g1 3 .51 0.5 3 2 h 5.26 0.207 i 0.76 0.0 3 0 j 3 .05 0.120 k 2.54 0.100 l 15.2 16.5 0.5 98 0.650 m2.2 9 0.0 9 0 n 0.71 0.02 8 r 1.65 0.065 to-257 mechanical data 011726 8 c
ordering information rhfl4913xx15 - rhfl4913xx25 - rhfl4913xx33 - rhfl4913xx50 16/19 9 ordering information table 5. order codes die flat-16 smd.5 to-257 terminal finish out. volt. q.ty level rhfl4913kp15-01v rhfl4913s15-03v rhfl4913esy1505v gold 1.5 v RHFL4913KP15-02V rhfl4913s15-04v rhfl4913esy1506v solder 1.5 v rhfl4913kp151 rhfl4913s151 rhfl4913esy151 gold 1.5 v em1 rhfl4913kp152 rhfl4913s152 rhfl4913esy152 gold 1.5 v em1=em2 +48h b.i. l491315die2v na 1.5 v l491315die2s na 1.5 v em1 rhfl4913kp25-01v rhfl4913s25-03v rhfl4913esy2505v gold 2.5 v qml-v rhfl4913kp25-02v rhfl4913s25-04v rhfl4913esy2506v solder 2.5 v qml-v rhfl4913kp251 rhfl4913s251 rhfl4913esy251 gold 2.5 v em1 rhfl4913kp252 rhfl4913s252 rhfl4913esy252 gold 2.5 v em1=em2 +48h b.i. l491325die2v na 2.5 v qml-v l491325die2s na 2.5 v em1 rhfl4913kp33-01v rhfl4913s33-03v rhfl4913esy3305v gold 3.3 v qml-v rhfl4913kp33-02v rhfl4913s33-04v rhfl4913esy3306v solder 3.3 v qml-v rhfl4913kp331 rhfl4913s331 rhfl4913esy331 gold 3.3 v em1 rhfl4913kp332 rhfl4913s332 rhfl4913esy332 gold 3.3 v em1=em2 +48h b.i. l491333die2v na 3.3 v qml-v l491333die2s na 3.3 v em1 rhfl4913kp50-01v rhfl4913s50-03v rhfl4913esy5005v gold 5.0 v qml-v rhfl4913kp50-02v rhfl4913s50-04v rhfl4913esy5006v solder 5.0 v qml-v rhfl4913kp501 rhfl4913s501 rhfl4913esy501 gold 5.0 v em1 rhfl4913kp502 rhfl4913s502 rhfl4913esy502 gold 5.0 v em1=em2 +48h b.i. l491350die2v na 5.0 v qml-v l491350die2s na 5.0 v em1
rhfl4913xx15 - rhfl4913xx25 - rhfl4913xx33 - rhfl4913xx50 ordering information 17/19 note: 3 v version is available on request. table 6. part number - smd equivalent st part number smd part number RHFL4913KP15-02V rhfl4913kp25-01v 5962f0253401vxc rhfl4913kp25-02v 5962f0253401vxa rhfl4913kp33-01v 5962f0253501vxc rhfl4913kp33-02v 5962f0253501vxa rhfl4913kp50-01v 5962f0253601vxc rhfl4913kp50-02v 5962f0253601vxa rhfl4913s25-03v 5962f0253402vyc rhfl4913s25-04v 5962f0253402vya rhfl4913s33-03v 5962f0253502vyc rhfl4913s33-04v 5962f0253502vya rhfl4913s50-03v 5962f0253602vyc rhfl4913s50-04v 5962f0253602vya rhfl4913esy2505v 5962f0253402vzc rhfl4913esy2506v 5962f0253402vza rhfl4913esy3305v 5962f0253502vzc rhfl4913esy3306v 5962f0253502vza rhfl4913esy5005v 5962f0253602vzc rhfl4913esy5006v 5962f0253602vza l491325die2v 5962f0253402v9a l491333die2v 5962f0253502v9a l491350die2v 5962f0253602v9a table 7. environmental characteristics parameter conditions value unit output voltage thermal drift -55c to +125c 40 ppm/c output voltage radiation drift from 0 kr ad to 300 krad at 0.55 rad/s 8 ppm/krad output voltage radiation drift from 0 krad to 300 krad, mil std 883e method 1019.6 6 ppm/krad
revision history rhfl4913xx15 - rhfl4913xx25 - rhfl4913xx33 - rhfl4913xx50 18/19 10 revision history table 8. document revision history date revision changes 05-may-2004 4 mistake in pin description smd.5 on table 3. 28-oct-2004 5 new order codes added - tables 4 and 5. 27-may-2005 6 the features, tables 4, 5 and the figures 1, 2 updated. 08-jun-2005 7 modified: p d on table 1, the r thjc for to-257 on table 2 and the tables 6 and 7, added die information. 26-aug-2008 8 added new output 1.5 v, modified: table 4 on page 6 , table 5 on page 16 and table 6 on page 17 . 02-oct-2008 9 modified: features on page 1 , application information on page 10 and smd.5 mechanical data on page 14 .
rhfl4913xx15 - rhfl4913xx25 - rhfl4913xx33 - rhfl4913xx50 19/19 please read carefully: information in this document is provided solely in connection with st products. stmicroelectronics nv and its subsidiaries (?st ?) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described he rein at any time, without notice. all st products are sold pursuant to st?s terms and conditions of sale. purchasers are solely responsible for the choice, selection and use of the st products and services described herein, and st as sumes no liability whatsoever relating to the choice, selection or use of the st products and services described herein. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. i f any part of this document refers to any third party products or services it shall not be deemed a license grant by st for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoev er of such third party products or services or any intellectual property contained therein. unless otherwise set forth in st?s terms and conditions of sale st disclaims any express or implied warranty with respect to the use and/or sale of st products including without limitation implied warranties of merchantability, fitness for a parti cular purpose (and their equivalents under the laws of any jurisdiction), or infringement of any patent, copyright or other intellectual property right. unless expressly approved in writing by an authorized st representative, st products are not recommended, authorized or warranted for use in milita ry, air craft, space, life saving, or life sustaining applications, nor in products or systems where failure or malfunction may result in personal injury, death, or severe property or environmental damage. st products which are not specified as "automotive grade" may only be used in automotive applications at user?s own risk. resale of st products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by st for the st product or service described herein and shall not create or extend in any manner whatsoev er, any liability of st. st and the st logo are trademarks or registered trademarks of st in various countries. information in this document supersedes and replaces all information previously supplied. the st logo is a registered trademark of stmicroelectronics. all other names are the property of their respective owners. ? 2008 stmicroelectronics - all rights reserved stmicroelectronics group of companies australia - belgium - brazil - canada - china - czech republic - finland - france - germany - hong kong - india - israel - ital y - japan - malaysia - malta - morocco - singapore - spain - sweden - switzerland - united kingdom - united states of america www.st.com

▲Up To Search▲

Price & Availability of RHFL4913KP15-02V

	To Download RHFL4913KP15-02V Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .